Tripp Lite UPS SMART1000RM1UN SmartPro 1U 120V 1kVA 800W 6 Outlets USB Retail
Tripp Lite UPS SMART1000RM1UN SmartPro 1U 120V 1kVA 800W 6 Outlets USB Retail
Overview
The SMART1000RM1UN SmartPro 120V 1kVA 800W Line-Interactive Sine Wave UPS provides battery backup and AC power protection against blackouts, brownouts, power surges and line noise that can damage electronics or destroy data. Ideal for backing up data centers, VoIP systems and network closets, the SMART1000RM1UN switches to 1kVA/800W battery mode in milliseconds to keep your connected equipment running long enough to save files and shut down safely with no data loss.
Protects connected mission-critical equipment against damage, downtime and data loss due to blackouts, brownouts, power surges and line noise. Pre-installed WEBCARDLX network interface permits remote UPS management.
• Corrects under- and overvoltages from 83V to 147V
• 6 NEMA 5-15R outlets—2 switchable via network interface
• Network power management and control capability
• Pre-installed WEBCARDLX network interface
• 14 min. runtime at half load; 4 min. at full load
OUTPUT
Output Volt Amp Capacity (VA): 1000
Output kVA Capacity (kVA): 1
Output Watt Capacity (Watts): 800
Power Factor: 0.8
Nominal Output Voltage(s) Supported: 110V, 115V, 120V
Nominal Voltage Details: 120v nominal output in battery mode
Frequency Compatibility: 60 Hz
Output Voltage Regulation (Line Mode): -21%, +8%
Output Voltage Regulation (Battery Mode): +/- 5%
Output Receptacles: (6) 5-15R
Load Management Receptacles: Two switchable single-outlet 5-15R load banks
Output AC Waveform (AC Mode): Sine wave
Output AC Waveform (Battery Mode): Pure Sine wave
INPUT
Rated input current (Maximum Load): 9.2A
Nominal Input Voltage(s) Supported: 120V AC
UPS Input Connection Type: 5-15P
Input Circuit Breakers: 15A
Recommended Electrical Service: 15A 120V
Input Cord Length (m): 3.05
Input Phase: Single-Phase
BATTERY
Full Load Runtime (min.): 4 min. (800w)
Half Load Runtime (min.): 14 min. (400w)
DC System Voltage (VDC): 24
Battery Recharge Rate (Included Batteries): Less than 4 hours from 10% to 90% (typical, full load discharge)
Internal UPS Replacement Battery Cartridge: RBC69-1U
Battery Access: Front panel battery access door
Battery Replacement Description: Hot-swappable, user replaceable batteries
Expandable Runtime: No
USER INTERFACE, ALERTS and CONTROLS
Switches: 2 Switches control off/on power status and alarm-cancel/self-test operation
Alarm Cancel Operation: Power-fail alarm can be silenced using alarm-cancel switch once silenced, alarm will re-sound to indicate low-battery status
Audible Alarm: Audible alarm indicates power-failure, overload and low-battery conditions
LED Indicators: 5 LEDs indicate line power, battery power, overload, voltage regulation and battery low/replace status
SURGE / NOISE SUPPRESSION
UPS AC Suppression Joule Rating: 450
EMI / RFI AC Noise Suppression: Yes
AC Suppression Response Time: Instantaneous
PHYSICAL
Included Mounting Accessory Description: Included mounting brackets support 2 and 4 post rackmount installation Optional 4POSTRAILKIT1U is available for additional support in 4 post rackmount applications
Primary Form Factor: Rackmount
Rack Height (U Spaces): 1
Cooling Method: Fan
UPS Housing Material: Steel
ENVIRONMENTAL
Operating Temperature Range: +32 to +104 degrees Fahrenheit / 0 to +40 degrees Celsius
Storage Temperature Range: +5 to +122 degrees Fahrenheit / -15 to +50 degrees Celsius
Relative Humidity: 0 to 95%, non-condensing
AC Mode BTU / Hr. (Full Load): 39
Battery Mode BTU / Hr. (Full Load): 816
AC Mode Efficiency Rating (100% Load): 99%
COMMUNICATIONS
Communications Interface: DB9 Serial, EPO (emergency power off), Pre-installed network card, Slot for SNMP/Web interface, USB
Network Monitoring Port Description: Includes pre-installed WEBCARDLX Network Management Card
PowerAlert Software: For local monitoring via the UPSs built-in communication ports, download
Communications Cable: USB and DB9 cabling included
WatchDog Compatibility: Supports Watchdog application, OS and hard-reboot restart options for remote applications
LINE / BATTERY TRANSFER
Transfer Time: 5 milliseconds AC to DC, 1 millisecond DC to AC
Low Voltage Transfer to Battery Power (Setpoint): 83
High Voltage Transfer to Battery Power (Setpoint): 147
SPECIAL FEATURES
Grounding Lug Back: panel grounding lug
Cold Start (Startup in Battery Mode During a Power Failure): Cold-start operation supported
High Availability UPS Features: Hot swappable batteries
Green Energy-Saving Features: Greater than 95% efficiency - GREEN UPS Individually controllable load banks
CERTIFICATIONS
UPS Certifications: Meets FCC Part 15 Category A (EMI),Tested to CSA (Canada), Tested to NOM (Mexico), Tested to UL1778 (USA)
Package Includes
SMART1000RM1UN SmartPro 120V 1kVA 800W Line-Interactive Sine Wave UPS
Pre-installed WEBCARDLX network interface
USB cable
DB9 cable
EPO cable
Mounting hardware
Owners manual
Item Dimension ( L inch x W inch x H inch)
23 x 24 x 7
Weight
36.00 lb
Warranty Information
2-year warranty
Overview
The SMART1000RM1UN SmartPro 120V 1kVA 800W Line-Interactive Sine Wave UPS provides battery backup and AC power protection against blackouts, brownouts, power surges and line noise that can damage electronics or destroy data. Ideal for backing up data centers, VoIP systems and network closets, the SMART1000RM1UN switches to 1kVA/800W battery mode in milliseconds to keep your connected equipment running long enough to save files and shut down safely with no data loss.
Protects connected mission-critical equipment against damage, downtime and data loss due to blackouts, brownouts, power surges and line noise. Pre-installed WEBCARDLX network interface permits remote UPS management.
• Corrects under- and overvoltages from 83V to 147V
• 6 NEMA 5-15R outlets—2 switchable via network interface
• Network power management and control capability
• Pre-installed WEBCARDLX network interface
• 14 min. runtime at half load; 4 min. at full load
OUTPUT
Output Volt Amp Capacity (VA): 1000
Output kVA Capacity (kVA): 1
Output Watt Capacity (Watts): 800
Power Factor: 0.8
Nominal Output Voltage(s) Supported: 110V, 115V, 120V
Nominal Voltage Details: 120v nominal output in battery mode
Frequency Compatibility: 60 Hz
Output Voltage Regulation (Line Mode): -21%, +8%
Output Voltage Regulation (Battery Mode): +/- 5%
Output Receptacles: (6) 5-15R
Load Management Receptacles: Two switchable single-outlet 5-15R load banks
Output AC Waveform (AC Mode): Sine wave
Output AC Waveform (Battery Mode): Pure Sine wave
INPUT
Rated input current (Maximum Load): 9.2A
Nominal Input Voltage(s) Supported: 120V AC
UPS Input Connection Type: 5-15P
Input Circuit Breakers: 15A
Recommended Electrical Service: 15A 120V
Input Cord Length (m): 3.05
Input Phase: Single-Phase
BATTERY
Full Load Runtime (min.): 4 min. (800w)
Half Load Runtime (min.): 14 min. (400w)
DC System Voltage (VDC): 24
Battery Recharge Rate (Included Batteries): Less than 4 hours from 10% to 90% (typical, full load discharge)
Internal UPS Replacement Battery Cartridge: RBC69-1U
Battery Access: Front panel battery access door
Battery Replacement Description: Hot-swappable, user replaceable batteries
Expandable Runtime: No
USER INTERFACE, ALERTS and CONTROLS
Switches: 2 Switches control off/on power status and alarm-cancel/self-test operation
Alarm Cancel Operation: Power-fail alarm can be silenced using alarm-cancel switch once silenced, alarm will re-sound to indicate low-battery status
Audible Alarm: Audible alarm indicates power-failure, overload and low-battery conditions
LED Indicators: 5 LEDs indicate line power, battery power, overload, voltage regulation and battery low/replace status
SURGE / NOISE SUPPRESSION
UPS AC Suppression Joule Rating: 450
EMI / RFI AC Noise Suppression: Yes
AC Suppression Response Time: Instantaneous
PHYSICAL
Included Mounting Accessory Description: Included mounting brackets support 2 and 4 post rackmount installation Optional 4POSTRAILKIT1U is available for additional support in 4 post rackmount applications
Primary Form Factor: Rackmount
Rack Height (U Spaces): 1
Cooling Method: Fan
UPS Housing Material: Steel
ENVIRONMENTAL
Operating Temperature Range: +32 to +104 degrees Fahrenheit / 0 to +40 degrees Celsius
Storage Temperature Range: +5 to +122 degrees Fahrenheit / -15 to +50 degrees Celsius
Relative Humidity: 0 to 95%, non-condensing
AC Mode BTU / Hr. (Full Load): 39
Battery Mode BTU / Hr. (Full Load): 816
AC Mode Efficiency Rating (100% Load): 99%
COMMUNICATIONS
Communications Interface: DB9 Serial, EPO (emergency power off), Pre-installed network card, Slot for SNMP/Web interface, USB
Network Monitoring Port Description: Includes pre-installed WEBCARDLX Network Management Card
PowerAlert Software: For local monitoring via the UPSs built-in communication ports, download
Communications Cable: USB and DB9 cabling included
WatchDog Compatibility: Supports Watchdog application, OS and hard-reboot restart options for remote applications
LINE / BATTERY TRANSFER
Transfer Time: 5 milliseconds AC to DC, 1 millisecond DC to AC
Low Voltage Transfer to Battery Power (Setpoint): 83
High Voltage Transfer to Battery Power (Setpoint): 147
SPECIAL FEATURES
Grounding Lug Back: panel grounding lug
Cold Start (Startup in Battery Mode During a Power Failure): Cold-start operation supported
High Availability UPS Features: Hot swappable batteries
Green Energy-Saving Features: Greater than 95% efficiency - GREEN UPS Individually controllable load banks
CERTIFICATIONS
UPS Certifications: Meets FCC Part 15 Category A (EMI),Tested to CSA (Canada), Tested to NOM (Mexico), Tested to UL1778 (USA)
Package Includes
SMART1000RM1UN SmartPro 120V 1kVA 800W Line-Interactive Sine Wave UPS
Pre-installed WEBCARDLX network interface
USB cable
DB9 cable
EPO cable
Mounting hardware
Owners manual
Item Dimension ( L inch x W inch x H inch)
23 x 24 x 7
Weight
36.00 lb
Warranty Information
2-year warranty
